Fish n Pull Wire Pulling System Review


Fish n Pull Wire Pulling System Review: Magnepull Alternatives?

Magnetic wire pulling system is one of the most popular DIY projects. There are many reasons why people like it so much. One reason is because it’s easy to build and doesn’t require any special skills or tools. Another reason is that it provides a sense of accomplishment when you successfully pull something out of your wall with a magnet! However, there are other alternatives to using magnets for pulling wires. Some of them include:

Lift chains (like these)

Wooden dowels and nails (like these)

Duct tape (like these)

These are all good options, but none of them really compare to magnets. They’re not very strong either, which means they don’t last long enough for some people. Other than that, the only downside is that they’re pretty expensive.

If you want to use magnets for pulling wires, then you need to make sure that you get the best quality possible.

The Best Magnetic Wire Puller: Magnepull

Magnepull is a company based in Australia that makes their own magnetic wire pullers. They offer several different models at various price points. Here’s what they have to say about themselves: “We believe that every home should have a simple solution for keeping their electrical wiring neat and tidy.”

The most popular model is the Deluxe 50mm model. It’s a big round magnet with a hook on one side and a handle on the other. They range in price from $35 to $229, depending on the size that you need.

Fish n Pull Wire Pulling System Review - realmanguide.net

If you’re going to be pulling wires out of your walls on a regular basis, then you should probably get one of the bigger ones. Even the largest one will only cost you around $150. That’s a small price to pay to keep your home from looking like a disaster zone!

Which model should I choose: Magnepull Alternatives or Fish n Pull?

As we mentioned earlier, one of the main benefits of magnets is that they’re super easy to use and you don’t need any special skills or tools. They also last longer than wooden dowels and nails. However, the downsides are that they’re more expensive than other options, and not as strong, which means they can only be used for lighter jobs. You just need to decide if the pros outweigh the cons for you personally.

We hope this article has been helpful to you. Good luck with your home improvement projects!

SaveSave

SaveSave

SaveSave

Mag-Pulls: The Newest Way To Fish Wires Through Your Walls

Fishing wires through walls: it’s a task that every DIYer dreads. Unless you’re some sort of wiring expert, you’ll probably end up making a mess of things. Even if you do know what you’re doing, it still takes a long time to drill holes in the exact right spots and thread the wires through them.

Even a small home can take all day if you don’t know what you’re doing.

Of course, there are tools that help with this job. Most people use the old-school method of using wooden dowels and nails to make holes in the wall. There’s also laser tools that give you the exact spots to drill.

Fish n Pull Wire Pulling System Review at realmanguide.net

But even these don’t work perfectly, and you still have to go through the process of threading the wires through the holes…

Or at least, you would, if it wasn’t for the newest innovation in home improvement: the high-performance magnetic wire puller! With this device, you just have to attach one end of your wire to the powerful magnet, push it through the wall, and when the magnet reaches the other side, simply pull on the handle to retrieve your wire. It’s much easier than using dowels and nails, not to mention faster.

In this guide, we’ll be reviewing five of the best magnetic wire pullers on the market, as well as going over some crucial tips that will help you get the most out of your tool. Let’s get started!

Best Magnetic Wire Pullers

Model Price Weight Rating Max jaw width Fish-n-Pull

Check Price 2 lbs 4.8/5 50mm Grip It and Pull

Check Price 2 lbs 4.8/5 50mm Delux 50mm

Check Price 7 lbs 3.8/5 50mm 50mm Magnetic Wire Puller Kit

Check Price 13 lbs 3.6/5 50mm

These are the five models that we believe offer the best value for your money. We’ll be going over their pros and cons, and giving you a sense of what to expect from each one so that you can choose the right product for your needs.

1. Fish-n-Pull The Fish-n-Pull is a 50mm jaw model, which means it’s able to securely grip 50mm holes, which are large enough for most wires used for home improvement projects.

Fish n Pull Wire Pulling System Review - Picture

The first thing that you’ll notice about this tool is that it has a fairly sleek, minimal design. While other models have a lot of decorative flourishes, the Fish-n-Pull has a clean, no-nonsense look that should please those who value function over form. The jaw is lined with powerful rare earth magnets that hold onto the wires that you’re pulling.

It’s made from durable stainless steel so it won’t rust, so you can feel free to put it out on your jobsite even if it’s raining. It’s also fairly lightweight at just two pounds, so you can lug it around without too much effort. The only drawback of this model is that the grip isn’t as substantial as some of the others on our list. If you’re going to be using it a lot, you might want to buy a pair of gloves so you don’t end up with sore hands. Pros: Lightweight

One of the most affordable options on our list

50mm grip is large enough for most wires Cons: Grip isn’t as substantial as some would like

2. Grip It and Pull If you want to save yourself a little money but don’t mind sacrificing a little quality, the Grip It and Pull is a great option.

It has a slightly smaller grip range than the Fish-n-Pull, but it’s also less expensive. It has a much more substantial grip than the former model, so if you’re going to be using the tool frequently, this might be a better option. Unfortunately, the quality of the materials isn’t as good.

The plastic feels significantly cheaper and you have to be careful with it since it’s more prone to breaking. It’s also on the heavier side at two pounds ten ounces, which means that it will tire your arm out a lot quicker. If you’re just using it every once in a while, though, it should be fine. The magnets on this tool aren’t very strong, so the grip isn’t as reliable as it could be. Thankfully, there’s a way to fix this: you can open up the clamp and add additional magnets to the inside of the clamp for more pull strength. Pros: Inexpensive

Heavier clamp is good for people who will be using it a lot

Can easily be modded for more grip strength Cons: Grip isn’t very reliable

Very lightweight clamp isn’t as good for people who will be using it a lot

3. Delux 50mm The Delux 50mm is very similar to the Grip It and Pull, except it has a slightly wider jaw opening.

This gives it a wider range and is able to handle larger wires for thicker cables. It’s made from stainless steel, like the Fish-n-Pull, so it should be fairly durable. Unfortunately, this one suffers from the same drawbacks as the Grip It and Pull.

The plastic feels a little cheap, it’s quite heavy at three pounds six ounces, and the grip isn’t always that reliable. It has a fairly sleek design, though, that will appeal to some people. It’s on the pricier side, but if you don’t mind paying a little extra money for a reliable cable puller, then this is a good option for you.

Fish n Pull Wire Pulling System Review on realmanguide.net

Pros: Stainless steel construction is very durable

Wider jaw opening is great for dealing with thicker wires Cons: Quite heavy

Plastic feels a bit cheap

Grip isn’t very reliable

4. Stalwart 50mm If you need a little more reach than the other models can offer, then this one by Stalwart is a great option.

It has the largest jaw opening, so it can easily accommodate a wide range of wires and cables. Unfortunately, the large size means that it’s not the most portable. It also doesn’t help that it weighs over three pounds.

Unless you really need that extra reach, you’re probably better off choosing one of the smaller models on our list. If portability isn’t a major concern for you, though, this one is tough to beat. The grip strength of this tool is very impressive. The jaws can easily crush ice, so you know it’s going to be able to handle even the thickest of cables. The grip is very comfortable, and the stainless steel construction makes it very durable. The only complaint is that it’s not the most attractive looking model, but if you need a tool that just gets the job done, this is a good option.

Pros: Very durable

Impressive jaw strength

Fish n Pull Wire Pulling System Review | realmanguide.net

Comfortable grip Cons: Very heavy

A bit too large and bulky

Loud and somewhat obnoxious looking (If you care about that)

5. Kincrome 52mm If you need an affordable option that still gets the job done, the Kincrome is a great choice.

The grip is more comfortable than you would expect from a tool in this price range. The handle is also made from die-cast metal for maximum durability and comfort. It’s not the sturdiest or most attractive option, but it should get the job done.

Unfortunately, this one suffers from the same problems as the Grip It and Pull. It’s quite heavy, at 2 pounds 7.5 ounces, and the grip strength isn’t always reliable. The jaw opening is also a bit on the small side, so it won’t be able to grab onto thicker cables. This is still a great option if you need something cheap and don’t mind making a few sacrifices.

Pros: Inexpensive

Comfortable grip

Stainless steel construction Cons: Quite heavy

Opening is a bit small

Grip strength isn’t reliable

6. Camco 515 This one is a little different from the rest of the models on our list.

Fish n Pull Wire Pulling System Review at realmanguide.net

It doesn’t use leverage to pinch the wires, instead clamping down on them using a gear driven mechanism. This model is quite heavy, weighing in at over four pounds, but that’s because it’s made from solid brass. It also won’t be able to grab onto thicker wires, like telephone cables, but it should be able to manage thinner wires without any problems.

The jaws are also coated with vinyl to ensure that they don’t cause any electrical shorts. Even if you don’t need to use this for your job, it would still be a great addition to your tool collection. It’s well constructed, and the unique design makes it a fun curiosity.

If you’re the kind of person that collects tools because of their novelty rather than their functionality, then this is the model for you. It’s made from solid brass and uses a gear driven mechanism, so it’s both fun to play with and fun to look at. It can clamp down on wires, but it’s not designed to handle anything larger than a coat hanger.

The vinyl-coated jaws are there to prevent it from causing electrical shorts. It’s very well made, but as with anything like this, it’s designed for novelty rather than practicality. If you like the way it looks and have the cash to spare, then buy it. If not, look at one of the other models.

You’ve Selected:

Klein Tools 515 Solid Brass Ratchet Cable Cutter

The jaw strength of this tool is quite impressive, and you know that it’s sturdy enough to perform the job without fail. The grip, while not as comfortable as the Grip-It, is still perfectly serviceable. The solid brass construction means that it’s both durable and attractive looking, which aren’t features you find often in a tool.

The price is a little high, but you decide that it’s worth it. Your hunt through the tool section has finally come to an end.

You hand over the money, collect your purchase and head on over to the gardening supplies.

Sources & references used in this article: